Różnice

Różnice między wybraną wersją a wersją aktualną.

--- pl:novitus_fp_config [2024/12/05 08:45] – karolina
+++ pl:novitus_fp_config [2025/07/18 10:04] (aktualna) – [Printer Port Settings] karolina
@@ Linia 13: / Linia 13: @@
 ''Ustawienia -> Konfiguracja -> Polaczenia -> Ustawienia Portow -> PC''
-- Ensure that the "Interfejs" option is set to ''TCP''.
+- Ensure that the "Interfejs" option is set to ''TCP''. - The remaining settings can be configured individually according to your preferences.
 === Enable "NOVITUS" Protocol ===
@@ Linia 37: / Linia 38: @@
 At this point, it's important to test whether the fiscal printer is ready to accept HTTP connections. Open PowerShell or any other shell application and issue an HTTP request to the IP address and port you configured in the previous step. For example, using PowerShell, you might issue the following command:
-{{ :mustand:ergo:webrequest.png }}
+{{ :pl:webrequest.png }}
 The response should indicate a ''StatusCode'' of 200, which confirms that the request was received successfully and the printer responded.
-{{ :mustand:ergo:200ok.png }}
+{{ :pl:200ok.png }}
 === Enabling HTTPS ===
@@ Linia 147: / Linia 148: @@
 Next, open the "Wiking2" software and follow the instructions pictured below to upload the certificate to the printer:
-{{:mustand:ergo:wiking1.png}}
+{{:pl:wiking1.png}}
-{{:mustand:ergo:wiking2.png}}
+{{:pl:wiking2.png}}
-{{:mustand:ergo:wiking3.png}}
+{{:pl:wiking3.png}}
-{{:mustand:ergo:wiking4.png}}
+{{:pl:wiking4.png}}
 After the certificate has been uploaded, restart the fiscal printer.
@@ Linia 159: / Linia 160: @@
 === Testing the HTTPS Connection ===
-To verify that HTTPS is working correctly, follow the same steps as before, but use the ''https://'' protocol instead of ''http://''.
+To verify that HTTPS is working correctly, follow the same steps as before, but use the https: protocol instead of http:
-For example:
+For example:   {{ :pl:httpsrequest.png }} The response should again indicate a ''StatusCode'' of 200, confirming a successful connection.   {{ :pl:200ok_1_.png }} Additionally, open a web browser and navigate to ''[[https://printerip:configured_port/api/v1]].''
-{{ :mustand:ergo:httpsrequest.png |}}
+**Note:** If you are using a custom Root CA, you may need to restart your browser. This ensures that the browser recognizes the newly installed Root CA and does not display certificate warnings. You should see a blank white page, indicating that the printer's API is accessible via HTTPS without any security warnings.
-The response should again indicate a ''StatusCode'' of 200, confirming a successful connection.
+===== Troubleshooting =====
-{{ :mustand:ergo:200ok.png |}}
+If you encounter issues during the setup, here are a few common troubleshooting steps:
-Additionally, open a web browser and navigate to ''https://printerip:configured_port/api/v1.'' **Note:** If you are using a custom Root CA, you may need to restart your browser. This ensures that the browser recognizes the newly installed Root CA and does not display certificate warnings. You should see a blank white page, indicating that the printer's API is accessible via HTTPS without any security warnings.
+  * **Is the printer connected to the local network via an Ethernet cable?** Ensure that the printer is properly connected and powered on.
+  * **Can the printer's IP address be reached from your computer?** Use tools like ''ping'' or ''telnet'' to check the connectivity between your computer and the printer.
+  * **Are you able to access the printer's configuration menu?** If not, check the physical connections and restart the printer.//   //
-===== Troubleshooting =====
+===== Ustawienia w Directo =====
-If you encounter issues during the setup, here are a few common troubleshooting steps:
+==== 1. Konfiguracja miejsca pracy (drukarka fiskalna) ====
+**Ścieżka:** **''Ustawienia ogólne → Lokalizacje''**
+Należy utworzyć tyle lokalizacji ile jest kas fiskalnych. W wybranej lokalizacji należy:
+  * W polu **Dostawca drukarki** wybrać odpowiedniego dostawcę urządzenia - **Novitus**
+  * W polu **IP internetu:Port **należy wpisać adres IP drukarki i podać numer portu komunikacyjnego
+{{:pl:2yfziyklyp.png}}
+==== 2. Ustawienie stawki VAT na paragonie ====
+Domyślnie drukarka ma przypisaną stawkę **A = 23% VAT**.
+Jeśli na paragonie ma być zastosowana inna stawka VAT
+**Ścieżka:** **''Ustawienia finansowe -> Kody VAT''**
+  * Otwórz kartotekę **Kody VAT**.
+  * W polu **PTU TOWARÓW NA PARAGONIE** przypisz odpowiednią literę (np. A, B, C, itd.) do wybranego kodu VAT.
+  * Upewnij się, że ta litera odpowiada konfiguracji w drukarce fiskalnej (zgodnie z jej dokumentacją techniczną).
-  * **Is the printer connected to the local network via an Ethernet cable?** Ensure that the printer is properly connected and powered on.
+{{:pl:uze2jeg5jp.png}}
-  * **Can the printer's IP address be reached from your computer?** Use tools like ''ping'' or ''telnet'' to check the connectivity between your computer and the printer.
-  * **Are you able to access the printer's configuration menu?** If not, check the physical connections and restart the printer.